Produktai skirti epoksiplastas 100 (9)

EG 91 Epoxy-polyurethane two-component elastoplastic and thixotropic sealant, for joints subject to traffic, where Shore A Hardness Scale = 65. The elongation-at-break is 70%. To be applied with a trowel or extruded into the suitably-taped sections of the joint (to protect adjacent surfaces). Resistant to contact with hydrocarbons (gasoline and diesel fuel). Horizontal sealing of joints in industrial flooring, even in the presence of chemical attacks and stresses from average-heavy traffic. Vertical sealing of joints in concrete works and products. The application and containment surfaces (joint walls) should be clean, dry, conveniently prepared and adequately resistant: free from dust, grease, soiling, crumbling and/or non-adhering parts and dry. The application surfaces must also be preliminarily treated with Protech Flex Primer. Add component B to component A taking care to pick up all the material contained in the packs, mix thoroughly with a mixer at a low number of revolutions, until a perfectly homogeneous mix is obtained; add the required load amount (component C) continue to mix until a perfectly homogeneous mixture is obtained, indicated by the uniform colour of the mixture. Apply the product mixed by trowelling or with extrusion guns. Do not apply with temperatures below + 5°C or higher than + 35°C and in the presence of surface stagnant water. Approximately 1.25 kg of EG 91 per cubic decimetre of joint volume to be sealed (1250 kg per cubic metre). Packaging: Kit of 5+2.5 kg UM: €/kg

Das erste Resin speziell für den 3D-Druck von Verschleißteilen und Zahnrädern. Für feinste Details (Präzision: ± 0,1 mm, kleine Zahnräder ab Modul m = 0,2) und enorme Lebensdauer durch integrierte Festschmierstoffe und die hohe Biegefestigkeit (90 MPa). Das 3D-Druck Kunstharz iglidur i3000 ist zur Verarbeitung auf DLP- und LCD-Druckern geeignet und wurde speziell für den Druck von Zahnrädern und Verschleißteilen entwickelt. Mit einer mindestens 30-mal bis 60-mal höheren Lebensdauer als herkömmliche 3D-Druck-Harze eignet sich iglidur® i3000 für jegliche Arten der Verschleißanwendung. Durch die hohe Auflösung von bis zu 35 μm können sehr filigrane Bauteile mit feinsten Details gedruckt werden. Die mechanischen Eigenschaften sind durch das Photopolymerisationsverfahren weitestgehend isotrop. Wenn Sie selbst über keinen DLP- oder LCD-Drucker verfügen, bieten wir auch die Fertigung von Bauteilen aus Resin in unserem hauseigenen 3D-Druck-Service an. Kontaktieren Sie uns gerne. Nettogewicht:1000 g Farbe:grau

2component epoxy paint for the protection of concrete floors, metal structures, etc. Does not contain solvents (100% solids). Features Excellent adhesion. Great penetration power. Good adhesion in wet substrate with high percentage of humidity. Good capacity for reaction at low temperatures and high percentage of humidity. Indoor and outdoor use.

Cortec VpCI® 386 Coating is a cutting-edge, water-based acrylic topcoat engineered to deliver superior corrosion protection for diverse metal substrates. Developed by corrosion prevention experts at Cortec Corporation, this innovative coating harnesses VpCI® technology to create an invisible shield against rust and oxidation. Environmentally friendly and easy to apply, it offers exceptional adhesion, durability, and versatility across various industries.Ideal for industrial equipment, manufacturing, automotive, marine, and construction applications, Cortec VpCI® 386 provides reliable protection while meeting stringent environmental standards.

Anstrichverträglicher Einkomponenten-Dichtstoff auf Basis Acryldispersion zur Abdichtung von Anschluss- und Bauteilfugen. Schnellregenfest. 2H Acryl 250 ist ein hochwertiger schnellregenfester plastischer Einkomponenten-Dichtstoff auf Basis Acryldispersion. Durch Verdunstung der Wasseranteile härtet 2H Acryl 250 zu einem alterungs-, witterungs- und UV-beständigen Dichtstoff aus. Kartuschen á 310 ml Folienbeutel á 310 ml Folienbeutel á 600 ml

Hochauflösender 3D-Druck mit Silikon. Silikon bietet herausragende Eigenschaften bezüglich Temperatur-, Chemikalien- und Witterungsbeständigkeit sowie eine hohe Elastizität. Das Material ist biokompatibel (getestet nach ISO 10993-05 und ISO 10993-10) und eignet sich für Dichtungen, Abdeckungen, Puffer und vieles mehr. Das Silikon können Sie in vier verschiedenen Härtegraden konfigurieren und online bestellen: - Shore 20A - Shore 35A - Shore 50A - Shore 60A

Wir bieten Ihnen eine große Auswahl an Technischen Kunststoffen und ermitteln für Sie den technisch und wirtschaftlich optimalen Kunststoff für Ihre Anforderungen.

Syntech HAG Acryl Syntech HAG Acryl is a four-component resin that reacts to form an elastic and durable gel. The properties of Syntech HAG Acryl are: • Good general chemical resistance. • Does not contain acrylamide, methacrylamide, formaldehyde or solvents. • Not inflammable. • Excellent adhesion on mineral building materials such as concrete, cement and bricks. • The reaction speed can be adjusted from a few seconds to several minutes. • When the injected cracks dry out due to temperature or groundwater level fluctuations the gel does not crack easily. • The hardened gel has excellent durability in wet-dry cycles. Syntech HAG Acryl components are supplied ready to use. Create 2 mixes in separate plastic buckets. Prepare only the quantity to be used each time. Solution 1: Syntech HAG Acryl component A (25 kg resin) mixed with Syntech HAG Acryl component B (2.5 kg catalyst). Solution 2: Syntech HAG Acryl component C (2 packs of 0.625 kg) mixed with clean tap water. Attention: The amount of water must be equal in volume to solution 1. When mixing resin, always use a wooden or stainless steel spatula. The reaction time depends on the temperature of the material, the structure of the building and the possible amount of water present. Higher temperature will speed up the reaction time and lower temperature will slow it down. It is advisable to carry out an on-site test, before injection, to observe and define the reaction time. To change the reaction time, only adjust the amount of Syntech HAG Acryl component C. The amount of the other components remains the same. Use a two-component stainless steel pump (manual, electric or pneumatic). Check that the pump and equipment are clean and that there is no residue from previous injection work. The two mixtures are fed into the pump separately, but are mixed homogeneously at a volumetric ratio of 1:1 in the pump's mixing head, before being injected through the pump nozzle. Check the quality of the concrete, as injection involves pressure. Sealing and waterproofing of cracks and cavities in walls, floors, concrete constructions, underground structures, etc. It can be used in constructions that are not permanently in contact with water (fluctuating groundwater level). Injection of very fine cracks. Determine the type and size of packers based on your pump and injection type. If reinforcing steel is present, try to locate it and plan the drilling pattern so that the reinforcement is not drilled. Drill holes at an angle of approximately 45° or less and in the direction of the crack. Make sure the hole goes through the crack. The distance of the drilled holes depends on the width of the crack. Place the packer in the hole. Prepare the pump to start the injection. The injection pressure varies depending on the structure and size of the crack. Start the injection at the lowest point of the crack. Continue injecting until resin flows out of adjacent packer(s). This is necessary to achieve uniform distribution of the material. Stop pumping, unplug and move on to the next packer. Continue the procedure until the crack is completely filled. After the material has cured, the packers can be removed. Holes drilled can be covered with Repar Tix Speedy HP quick-setting mortar. Clean and rinse the pump equipment with water whenever there is a stoppage longer than 15 minutes and, after completing the injection, rinse with a sufficient amount of water. Make sure the pump is clean and stop only when clean water comes out of the pump. The consumption of the product depends on the size of the empty volume to be filled. Can 25 kg [A] - Plastic can 2.5 kg [B] - Canister 0.625 kg [C] - Canister 0.625 kg [D] - Kit: 1 Can 25 kg [A] + 1 Plastic can 2.5 kg [B] + 1 Canister 0.625 kg [C] + 1 Canister 0.625 kg [D]

2H Acryl 150 mit Quarzsand ist ein elastoplastischer Dichtstoff auf Acryldispersionsbasis für innen und außen. Einkomponentiger Acrylatdichtstoff für den Innen- und Außenbereich mit einer max. Bewegungsaufnahme von 10%. Putzähnliche Oberfläche zum Verschließen von Rissen in Putz und Mauerwerksflächen innen und außen. Verpackung in 310ml Kartusche.